Small depressions in dried paint film are caused by pockets of air or entrapped solvent in the wet paint film.  There depressions can occur during application because of improper preparation of the roller cover.  In the case of solvent entrapment, they occur shortly after the intermediate coat or topcoat has been applied over the primer coat>  They cal also result from topcoating a solvent-based product too quickly, using a new roller cover without proper preparation, over-shaking the pa8int, or painting in excessively high temperatures.  Improper use of solvents when thinning the coating may also cause cratering.

In you live in the Greater Vancouver Area aka GVRD in British Columbia..please call 604-PAINTER to receive sevice from the Best painting contractors in Canada:  www.vancouversbestpainters.com .  If you have a large industrial project then call 604-PAINTER and ask for our industrial division.  www.vancouverindustrialpainting.com

Regards

Rick Andeson

Brush marks are slight ridges in dry paint film and are often due to poor-quality applicators.  If the polyester or nylon filament of a brush is not finished properly, it will leave marks.  Other cause of brush marks include:

A porous surface that absorbs too much coating, excessive brushing, applying too little paint, using the wrong thinner, not allowing enough drying time between coats.  Brush marks will also occur in paint films that dry too radily.  Water-based materials typically show brush makrs more than oil-based paints. 

Solution for Brush Marks

Always use top-quality applicators.  Brushes should have tapered bristles, properly flagged and tipped.  Smooth the surface by sanding before repainting or the brush marks will show through the new coat.  If the surface is porous, a primer should be applied.  Be sure to use a recommended thinner if the coating is too thinck, and allow the paint to dry completely between coats.  If you need any more information or are in need of an excellent painting company in Vancouver, British Columbia then don’t hesitate to call 604-PAINTER or visit the best painting contractors in the Greater Vancouver area:  www.vancouversbestpainters.com.  Be sure to visit our industrial site for the larger commercial or industrial projects you might have.  www.vancouverindustrialpainting.com

Rick Anderson

www.604painters.com

One of the number one errors I have witnessed over the past 30 years is the painting applicator does not ‘load up’ or hold enough paint coatings on his brush or roller.  If too much time is neeeded to complete a painting project because of constant reloading of the roller, either the roller cover does not contain enough fabric or the fabric used does not meet the requirments for a particular paint coating.  This problem occurs because the wrong type of applicator is ued or because the applicator is of low quality.  If hti sproblem occurs when using a brush, the bristles of the brush may be too short.  This problme can also be caused by mismathcing the applicator and the coating or by over-thinning the coating.

www.vancouversbestpainters.com www.vancouverindustrialpainting.com www.604painters.com

for the best painting contractors in the Vancouver area please call Vancouver’s Best Painters 604-PAINTER

At this point in my www.vancouversbestpainters.com postings, you have learned a lot about selecting the proper coating, preparing the coating for application, and using the appropriate tools in the proper way to apply the coating,  The next number of postings will help reinforce those principles by reviewing what happens when one of the principles is violated.

www.604painters.com www.vancouversbestpainters.com www.vancouverindustrialpainting.com

Peeling, blistering, crackiing, and chalking are just some of the symtoms of paint failure.  Most adhesion failures are caused by improper surface prparation or moisture problems such as high indooor humidity or moisture trapped in the substrate.

In the following articles by www.vancouversbestpainters.com (painters painting in Vancouver) I will show how to recognise and correct problems caused by improprer preparation and application of coatings, as well as causes of (and solutions for) coating discolouration).  If you experience a coating failure, you should not assume that there was a problem in the manufacturing process.  Such problems are rare because of the extensive quality controls used in the blending of coatings.  If you have a failure that you cannot find a reason for, contact the coating manufacturer’s representative in your area for assistance.  He will be able to help you determine the cause of the problem.

www.604painters.com www.vancouverindustrialpainting.com www.vancouversbestpainters.com

call:  604-PAINTER (604) 724-6837

Very nice colours for this Heritage Home in East Vancouver

1) Tip #1: Return every phone call within 24 hrs.

Alternative

2) Arrive early, or at least phone ahead if you are running late. If the customer does not feel you respect their time, they will believe you don’t respect them.

3) Dress neatly and shave, and, when you arrive, take off your shoes at the door. You onlyh get one chance to make a first impression.

4)Have a positive attitude when you greet the customer with a handshake and smile, and look them in the eyes. The job can be won or lost on the threshold of the home.

5) Turn off your cell phone on estimates—call interruption annoy the customer—as it makes them feel unimportant.

6) Everyone is different. Watch for body language and adjust your conversation to ease their concerns right away

7) Never show your own irritation—no matter what. They may nor be feeling well or have had a bad day. Always be professional

Let the customer walk in front of you—it’s a sign of respect.

9) Let the customer talk and explain everything they want, and then ask questions.

10) Take notes as you go through the job. Always have two pens handy.

11)Take the time to look closely at the job and be specific about what you intgend to do to repair, restore and paint.

12) Show your portfolio. The more pictures, letters of recommendation and newspaper or trade clips you have, the easier your selling job will be.