Inadequate sealing of surfaces with varying porosity may, after painting, cause a non-uniform sheen.  If shiny spots are noticeable, this problem is sometimes referred to as flashing by www.vancouversbestpainters.com and www.604painters.com Unevenapplication can result in varying film thicknesses and uneven gloss.  Fog or moisture on the paint film during drying flattens high-gloss finishes.  Temperature variations during drying also affect gloss.  Areas surrounding nail heads and wall studs tend to retain gloss because metal conducts heat and speeds up drying time; also, metals are nonporous, which improves gloss.  In addition, painting over a paint film that is not thoroughly dry or that is too soft can cause uneven gloss.

According to www.vancouversbestpainters.com improper amounts of thinner or other addittives sometimes cause uneven gloss.

Rick Anderson

www.vancouversbestpainters.com

www.604painters.com

www.vancouverindustrialpainting.com

According to Rick Anderson of www.vancouversbestpainters.com and www.604painters.com, painters painting in the Vancouver area, sagging has several possible causes.  Applications over a hard glossy finish is a common cause. Other causes include applying too much paint, excessive thinning, or application over a residual film left by a washing compound.

Sagging also can be caused by using too much solvent or using solvents other than those recommended by the coating manufacturer.  Painting cold surfaces will sometimes cause sagging.  According to Vancouver’s Best Painters www.vancouversbestpainters.com and Vancouver Industrial Painting www.vancouverindustrialpainting.com the solution for sagging is to always sand glossy finishes before painting them.  Liquid preparation designed to soften and clean hard coatings are available where sanding dust is a problem.  To determine if the paint is being applied too thickly, use a wet film gauge or measure the square footage covered per gallon of the sagging coat and compare it to the recommended spreading area.  If the rate is too low, increase it by applying a lighter coat or even by thinning the paint if necessary: however, thinning itself may cause the paint to sag.

Sometimes in cold weather, paint stored in cold areas thickens.  Instead of using paint thinner in these cases, allow the paint to warm up naturally.  Do not paint a surface that feels cold to the touch.  Do not paint when humidity exceeds 85%, as drying time will be slower and this can also cause sagging.  If saggin is noted during application despite all precautions, try brushing upward with long, even strokes, wiping the brush after each stroke.

Rick Anderson www.vancouversbestpainters.com www.604painters.com www.vancouverindustrialpainting.com call: 604-painter now!

Poor hiding of color is usually caused by applying too little paint.  However, keep in mind that reds and yellows do not cover well.  Other causes include a radical color change from one coat to the next, the underlying surface being too porous, the use of the a poor-quality applicator, excessive paint thinning, or inadequate mixinf of the paint.  Some low-cost one coat paints will not provide good hiding:

Solution for poor hiding:  Usually, an additional coat or coats of the same material and color, applied with a good quality tool at the recommended spreading rate, will provide adequate hiding.  The exceptions are radical color changes and extremely porous surfaces, which require a prime coat is tinted toward the finish color.  Make sure to follow the manufactuers recommendations for thpe and size of applicators and purchase good quality tools.  Refer to the recommended thinning list of the coating lable or ask your local independent supplier.  Be careful not to over thin. 

Contrary to popular opinion, deeper colors do not necessarily hide better than lighter tones.  The degree of hiding is due largely to white hiding pigment, some of which must be removed from white bases in order to tint deeper colors.  Therefore, deep color bases have less white hiding pigment than pastel and medium tones.

Craters should be sanded out and the surface repainted.  If they are not removed befefore the new coat is applied, they will show through.  Before using new roller covers, immerse them in the paint and roll them out a few times to expel air.  After a can has been shaken, it should be left to sit until all the bubbles and foam disappear.  Sometimes when painting on a hot day, the coating will dry too quickly and prevent the bubbles from flowing out during applications.  If this occurs, try adding a small amount of thinner to the paint.  Avoid using high-speed mixers with elastomeric multicolor coatings.

www.vancouversbestpainters.com www.606painters.com www.vancouverindustrialpainting.com www.renaissancepainters.ca www.torontosbestpainters.com

Small depressions in dried paint film are caused by pockets of air or entrapped solvent in the wet paint film.  There depressions can occur during application because of improper preparation of the roller cover.  In the case of solvent entrapment, they occur shortly after the intermediate coat or topcoat has been applied over the primer coat>  They cal also result from topcoating a solvent-based product too quickly, using a new roller cover without proper preparation, over-shaking the pa8int, or painting in excessively high temperatures.  Improper use of solvents when thinning the coating may also cause cratering.

In you live in the Greater Vancouver Area aka GVRD in British Columbia..please call 604-PAINTER to receive sevice from the Best painting contractors in Canada:  www.vancouversbestpainters.com .  If you have a large industrial project then call 604-PAINTER and ask for our industrial division.  www.vancouverindustrialpainting.com

Regards

Rick Andeson

Brush marks are slight ridges in dry paint film and are often due to poor-quality applicators.  If the polyester or nylon filament of a brush is not finished properly, it will leave marks.  Other cause of brush marks include:

A porous surface that absorbs too much coating, excessive brushing, applying too little paint, using the wrong thinner, not allowing enough drying time between coats.  Brush marks will also occur in paint films that dry too radily.  Water-based materials typically show brush makrs more than oil-based paints. 

Solution for Brush Marks

Always use top-quality applicators.  Brushes should have tapered bristles, properly flagged and tipped.  Smooth the surface by sanding before repainting or the brush marks will show through the new coat.  If the surface is porous, a primer should be applied.  Be sure to use a recommended thinner if the coating is too thinck, and allow the paint to dry completely between coats.  If you need any more information or are in need of an excellent painting company in Vancouver, British Columbia then don’t hesitate to call 604-PAINTER or visit the best painting contractors in the Greater Vancouver area:  www.vancouversbestpainters.com.  Be sure to visit our industrial site for the larger commercial or industrial projects you might have.  www.vancouverindustrialpainting.com

Rick Anderson

www.604painters.com

At this point in my www.vancouversbestpainters.com postings, you have learned a lot about selecting the proper coating, preparing the coating for application, and using the appropriate tools in the proper way to apply the coating,  The next number of postings will help reinforce those principles by reviewing what happens when one of the principles is violated.

www.604painters.com www.vancouversbestpainters.com www.vancouverindustrialpainting.com

Peeling, blistering, crackiing, and chalking are just some of the symtoms of paint failure.  Most adhesion failures are caused by improper surface prparation or moisture problems such as high indooor humidity or moisture trapped in the substrate.

In the following articles by www.vancouversbestpainters.com (painters painting in Vancouver) I will show how to recognise and correct problems caused by improprer preparation and application of coatings, as well as causes of (and solutions for) coating discolouration).  If you experience a coating failure, you should not assume that there was a problem in the manufacturing process.  Such problems are rare because of the extensive quality controls used in the blending of coatings.  If you have a failure that you cannot find a reason for, contact the coating manufacturer’s representative in your area for assistance.  He will be able to help you determine the cause of the problem.

www.604painters.com www.vancouverindustrialpainting.com www.vancouversbestpainters.com

call:  604-PAINTER (604) 724-6837

1) Tip #1: Return every phone call within 24 hrs.

Alternative

2) Arrive early, or at least phone ahead if you are running late. If the customer does not feel you respect their time, they will believe you don’t respect them.

3) Dress neatly and shave, and, when you arrive, take off your shoes at the door. You onlyh get one chance to make a first impression.

4)Have a positive attitude when you greet the customer with a handshake and smile, and look them in the eyes. The job can be won or lost on the threshold of the home.

5) Turn off your cell phone on estimates—call interruption annoy the customer—as it makes them feel unimportant.

6) Everyone is different. Watch for body language and adjust your conversation to ease their concerns right away

7) Never show your own irritation—no matter what. They may nor be feeling well or have had a bad day. Always be professional

Let the customer walk in front of you—it’s a sign of respect.

9) Let the customer talk and explain everything they want, and then ask questions.

10) Take notes as you go through the job. Always have two pens handy.

11)Take the time to look closely at the job and be specific about what you intgend to do to repair, restore and paint.

12) Show your portfolio. The more pictures, letters of recommendation and newspaper or trade clips you have, the easier your selling job will be.